Contents

Parts overview

For installers

Installing Wall mount
Installing Speakers
Installing Bluetooth Amplifier

For users

Set up for use

Parts overview

The supplied parts differ according to the type of audio system. All N-Joy Audio systems are supplied with the N-Joy Controller. In some sets, for example, the speakers and/or WiFi Audio Amplifier are not included.

N-Joy Controller
Bluetooth Amplifier
Speaker set

Installing Wall mount

The Wall Mount is also the charger for the N-Joy Controller. The Wall mount should be placed in a strategic location with good WiFi reception. There are three ways to supply power to the Wall mount.

A. Installation: with supplied USB adaptor and the 300 cm USB charging cable (recommended)

The best way to integrate the wall mount beautifully into the bathroom.


  1. Run a 16 mm or 5/8 inch electrical conduit through the place where you wish to install the wall mount. This can be done by using a bend, just as when installing a thermostat. Through this tube you can lead the USB cable to a wall socket, for example behind the ceiling or in another room. The length of this tube may not exceed 250 cm.
  2. Plug the supplied adapter into the wall socket and connect the USB cable to it. Connect the Micro-USB to the back of the wall mount.
  3. Make sure that the surface where you want to place the wall bracket is clean, dry and free of grease. Remove the protective film from the adhesive strip on the back of the wall mount. Place the wall mount and press firmly for 5 seconds. The wall mount is now fixed and ready for use.

TIP! Before attaching the wall mount to the wall, please make sure that the wall mount provides the controller with power. The wall mount is not easily removed.

B. Mounting: With supplied USB adaptor and 300 cm USB charging cable

The USB cable remains in view with this assembly method.


  1. Connect the Micro-USB to the back of the wall mount. Plug the supplied adapter into the wall socket and connect the USB cable to it.
  2. Make sure that the surface where you want to place the wall bracket is clean, dry and free of grease. Remove the protective film from the adhesive strip on the back of the wall mount. Place the wall mount and press firmly for 5 seconds. The wall mount is now fixed and ready for use.

TIP! Before attaching the wall mount to the wall, please make sure that the wall mount provides the controller with power. The wall mount is not easily removed.

C. Built-in: With the optional EMCISET installation set

You need the optional EMCISET for this.

CAUTION! This product may only be installed in Zone 3. See the drawing below to determine the correct location.


  1. Build the flush-mounting box in the wall. Pull two electrical wires (230V) and let them protrude 10 cm from the flush-mounting box.


  2. Connect the flush-mounting adapter and place it in the flush-mounting box. Push the flush-mounting adapter all the way in to the end of the flush-mounting box. Plug the Micro USB into the back of the wall mount.


  3. Make sure that the surface on which you want to place the wall mount is clean, dry and free of grease. Remove the cover from the adhesive strip on the back of the wall mount. Now place the wall mount exactly over the flush-mounting box and press firmly for 5 seconds. The wall mount is attached and ready for use.

TIP! Before attaching the wall mount to the wall, please make sure that the wall mount provides the controller with power. The wall mount is not easily removed.

Installing Speakers

This is followed by the installation of the speakers. There are a few important points to bear in mind when installing a WiFi audio speakers.

When these requirements are met, the speakers can be installed in the ceiling without any problems.

  1. Use the template to determine the hole in the ceiling and saw/cut it out.


  2. 2. Before installing the speaker, connect the Bluetooth amplifier and place it through the speaker hole on top of the ceiling. See next section for details.
  3. Connect the speaker wire to the speaker.


  4. Place the speaker.



    Rumba and Twist speakers
    The speakers are equipped with a clamping system. Open the clamps and put them through the hole. The speaker will lock itself in place.

    Samba and Zumba speakers
    Place the speaker in the hole. Using a screwdriver, tighten the 4 screws. This will open up the hooks on the back and secure the speaker in place.

    CAUTION! Use a screwdriver, not a screw machine.

Installing Bluetooth Amplifier

The Bluetooth amplifier is usually placed on top of the ceiling. Because of this, there are a few important points that need to be taken into account.

Below, we describe the step-by-step plan for connecting the cables to the amplifier.

1. Cut the speaker cable to size and strip the ends.
2. Connect this to the amplifier. Red in plus (+), black in minus (-).
3. Screw the antenna on.
4. If an AquaSound TV is present, it can now be connected to the INPUT.
5. Connect the adapter and plug it into the mains.

After this, the Bluetooth amplifier can be placed on top of the ceiling through the speaker hole.

Set up for use

The connection of the Bluetooth amplifier to the N-Joy Controller is easy to set up. Follow the steps in the N-Joy Controller.

When the N-Joy Controller has gone through its first-time installation, you can choose which streaming services to install. Some services require a subscription.

TuneIn Radio

The world's most used online radio. Choose from thousands of radio stations. A subscription is not required for this service.

Spotify

Millions of songs at your fingertips for hours of entertainment.

Apple Music

Apple Music gives artists a global stage and the tools to create music, so you can listen to it easily.

Deezer

Deezer is a music streaming service which gives you access to more than 90 million tracks worldwide and other audio content such as podcasts.

Tidal

Global streaming service with millions of songs and original content.

Shuttle Player

MP3 files stored in the controller come to life with the Shuttle Player.

Your N-Joy bathroom radio is therefore ready for hours of listening pleasure! In the unlikely event that you encounter problems that cannot be solved with this manual, please do not hesitate to contact us.

Contents

Parts overview

For installers

General installation tips
Mounting with the Backbox
Mounting with the VESA bracket

For users

Set up for use

Parts overview

The components supplied vary according to the type of Bathroom TV.

Built-in Bathroom TV
Surface mount Bathroom TV

General installation tips

The AquaSound Bathroom TV is available as a built-in version that is built into the wall, as well as a surface version that comes with a VESA bracket. Please note that a surface mounted TV cannot be built in without the backbox and vice versa.

The Bathroom TV comes with a so-called Mediabox. This is the computer of the Bathroom TV and is connected by a 150 cm long cable. This Mediabox can simply be placed in the backbox of the build-in version. When surface mounting the Bathroom TV, the Mediabox should be placed in a place where it will not get wet.

CAUTION! When building in the TV, the viewing angle of the display must be taken into account. Make sure that the TV is not mounted too high.

CAUTION! The cable between the TV and the Mediabox comes with a connector of about 50mm wide. Because of this, this cable cannot be pulled through normal electrical cables, but only through feed-through ducts. The minimum size of the wall duct that will be needed is 55 x 18 mm.

TIP! Before installing the Bathroom TV, think about the connections to the Mediabox. More information below.

Before placing the TV, it is wise to immediately pull the right cables to the location where the Mediabox will be placed. An absolute minimum is the cable from the adapter.

It is advisable to also run an internet cable to ensure extra stability for the smart functionality of the Bathroom TV. Optionally, the TV can be equipped with a coaxial connection for digital television reception.

If it is not possible to connect an internet cable to the Mediabox, then a good WiFi reception must be ensured at the place where the Mediabox will be installed.

Mounting with the Backbox (built-in)

The outer dimensions of the Backbox are 665 x 447 mm, with a depth of 76 mm. Make a cutout in the wall of the same size. Screw the Backbox to the wall on both sides. The front of the Backbox should fall flush with the front of the tiles/finished wall.

There is room in four places for an optional feed-through, which can be used for the cable to the Mediabox. But it is recommended to simply mount the Mediabox in the Backbox.

Placing the TV in the Backbox is self-evident.

1. Connect the internet cable to the Mediabox. (Optional)
2. Connect the coax to the Mediabox. (Optional)
3. Connect the DC Adapter to the Mediabox.
4. Connect the cable between the TV and the Mediabox.
5. Use a screwdriver to secure this cable.
6. Place the TV in the Backbox.
7. The magnets in the Backbox will ensure that the Bathroom TV stays firmly in place.

Mounting with the VESA bracket (surface)

Mounting the VESA bracket is easy. Take the bracket apart and mount the right parts on the wall and behind the TV. Then hook the TV part on the wall part and screw it down.

The included mounting materials are intended for mounting on solid masonry or concrete. Appropriate measures should be taken with other walls, e.g. of hollow bricks, plasterboard or lightweight wall constructions.

TIP! Behind the TV and next to the VESA bracket, the feed-through tube can be placed so that the cable can be neatly concealed.

CAUTION! When installing the Mediabox, bear in mind that it must be placed in a place where no water can get in. The cable length is a limiting factor here.

Set up for use

When the TV is switched on for the first time, it will start a configuration in which the TV can be set up easily. Here you can connect to the home network. The channels can also be set. Below, we describe the three most common methods.

When using digital DVB television, in some cases a CI+ module with a smart card must first be obtained from the provider.

A. DVB-C setup: Ziggo Cable TV
At Ziggo, you can receive TV both with and without a CI+ module. Please note that without a CI+ module, fewer channels are available. The reception settings are also different.

The reception settings can be found below. These data can be entered in the settings.

More information about Ziggo Cable TV DVB settings: Click here!
More information about Ziggo Cable TV with a CI+ module: Click here!

B. DVB-T2 setup: KPN Digitenne
For KPN Digitenne, a CI+ module is required. Without a CI+ module, only the public broadcasters can be received.

When using KPN Digitenne, the TV will search for channels by itself, provided there is a good signal on the antenna. This search can be started from the settings.

More information about KPN Digitenne with a CI+ module: Click here!

C. Setting DVB-S2: CanalDigitaal Satellite TV
With CanalDigitaal, a CI+ module is required. Without a CI+ module you can still watch unencrypted foreign channels, but not Dutch channels.

When using CanalDigitaal Satelliet TV the TV will search for channels by itself, provided there is a good signal on the dish. This search can be started from the settings.

More information about CanalDigitaal Satelliet TV with a CI+ module: Click here!

With this your Bathroom TV is completely ready for use! In case there are any problems that you cannot solve with this manual, please do not hesitate to contact us.

Contents

Parts overview

For installers

Installing Speakers
Installing Bluetooth Amplifier

For users

Set up for use

Parts overview

The components supplied vary depending on the type of audio system. In some sets, for example, the speakers are not included.

Bluetooth Amplifier
Speaker set

Installing Speakers

There are a few important points to bear in mind when installing Bluetooth audio system speakers.

When these requirements are met, the speakers can be installed in the ceiling without any problems.

  1. Use the template to determine the hole in the ceiling and saw/cut it out.


  2. 2. Before installing the speaker, connect the Bluetooth amplifier and place it through the speaker hole on top of the ceiling. See next section for details.
  3. Connect the speaker wire to the speaker.


  4. Place the speaker.



    Rumba and Twist speakers
    The speakers are equipped with a clamping system. Open the clamps and put them through the hole. The speaker will lock itself in place.

    Samba and Zumba speakers
    Place the speaker in the hole. Using a screwdriver, tighten the 4 screws. This will open up the hooks on the back and secure the speaker in place.

    CAUTION! Use a screwdriver, not a screw machine.

Installing Bluetooth Amplifier

The Bluetooth amplifier is usually placed on top of the ceiling. Because of this, there are a few important points that need to be taken into account.

Below, we describe the step-by-step plan for connecting the cables to the amplifier.

1. Cut the speaker cable to size and strip the ends.
2. Connect this to the amplifier. Red in plus (+), black in minus (-).
3. Screw the antenna on.
4. If an AquaSound TV is present, it can now be connected to the INPUT.
5. Connect the adapter and plug it into the mains.

After this, the Bluetooth amplifier can be placed on top of the ceiling through the speaker hole.

Set up for use

Using a Bluetooth Audio System is very simple. Pairing works in the same way as with Bluetooth wireless earphones, headphones and speakers. Smartphones can connect by going to the Bluetooth settings and finding the AquaSound system there.

With this, your Bluetooth audio system is ready for hours of listening pleasure! In the unlikely event that you encounter problems that you cannot solve with this manual, please do not hesitate to contact us.

Contents

Parts overview

For installers

Installing Speakers
Installing WiFi Audio Amplifier

For users

Set up for use

Parts overview

The components supplied vary depending on the type of audio system. In some sets, for example, the speakers are not included.

WiFi-Audio Amplifier
Speaker set

Installing Speakers

There are a few important points to bear in mind when installing WiFi audio system speakers.

When these requirements are met, the speakers can be installed in the ceiling without any problems.

  1. Use the template to determine the hole in the ceiling and saw/cut it out.


  2. Before placing the speaker, connect the WiFi-Audio amplifier and place it through the speaker hole on top of the ceiling. See the next section for details.
  3. Connect the speaker wire to the speaker.


  4. Place the speaker.



    Rumba and Twist speakers
    The speakers are equipped with a clamping system. Open the clamps and put them through the hole. The speaker will lock itself in place.

    Samba and Zumba speakers
    Place the speaker in the hole. Using a screwdriver, tighten the 4 screws. This will open up the hooks on the back and secure the speaker in place.

    CAUTION! Use a screwdriver, not a screw machine.

Installing WiFi Audio Amplifier

The WiFi audio amplifier is usually placed on top of the ceiling. Because of this, there are a few important points that have to be taken into account.

We recommend a LAN cable over a WiFi connection, for added stability to your listening experience.

Below, we describe the step-by-step plan for connecting the cables to the amplifier.

1. Cut the speaker cable to size and strip the ends.
2. Screw it into the terminal block. Red in plus (+), black in minus (-).
3. Insert the terminal block into the amplifier.



4. Connect the LAN cable, if available.
5. Screw the antenna, if present.
6. If an AquaSound TV is present, it can now be connected to the AUX-IN / LINE-IN.
7. Connect the adapter and plug it into the power socket.

After this, the WiFi-Audio amplifier can be placed on top of the ceiling through the speaker hole.

Set up for use

The inclusion of the WiFi-Audio amplifier in the WiFi home network is done using the SmartSonix app. Follow the steps in the app.

CAUTION! Turn off the 4G/5G data connection on your smartphone while connecting a WiFi Audio amplifier to the WiFi home network.

The SmartSonix app is available for Android and iOS devices.


TIP! If the WiFi Audio Amplifier asks for a password, it will be 88888888.

TIP! When the WiFi Audio amplifier is connected to a LAN cable, it doesn't need to be included in the WiFi home network, it is already connected. The app will find it immediately.

TIP! If you have problems including the WiFi-Audio amplifier in the WiFi home network, it might help to reset the amplifier. Below we explain how this works.

WMA30 At the back of the AUX-IN jack is the reset button. Use a toothpick to reach it. Press this button twice and the amplifier will indicate through the speakers that it is in Setup Mode.

WMA50 / WMA70 Push the WPS button twice. After that the amplifier will tell you through the speakers that it is in Setup Mode.

Your WiFi Audio System is now ready for hours of listening pleasure! In case there are any problems you cannot solve with this manual, please do not hesitate to contact us.

crossmenu